New Vespa oil seals - shaft seals from bgm PRO - Vespa & E10?
bgm PRO shaft seals made of high-quality and ethanol-resistant (E10) FKM / Viton® *
New: now also for Vespa Wideframe, GS3, Faro Basso etc .: We have ours Oil seal portfolio expanded with modern Simmerrings from bgm and can now be used for almost every classic Vespa Wave doctrines made of FKM / Viton® offer:
PERFECT SIZE
The bgm PRO Simmerrings have the perfect dimensions that guarantee easy installation, optimal function and a long service life. The large shaft seal on the clutch side, for example on old Vespas, has bgm PRO over a height of 7 mm, instead of the usual ones from other manufacturers 6,5 mm.
This is how the bgm PRO Simmer ring on the original factory information from Piaggio. If you have ever taken apart an old and original Vespa engine, you may have noticed that a large one comes from the factory Shaft seal was installed with a height of 7mm.
FLOATING CRANKSHAFT
In old engines, the crankshaft bearings are 'floating'. This means that the bearing is not fixed and it can be moved axially (horizontally laterally) in the motor housing. This shift takes place, for example, under load due to the axial force of the helically toothed primary drive. If the crankshaft shifts too much, this can of course have an effect on the ignition and also on the function of the clutch. The aim should therefore be to have as little unnecessary play as possible.
The stop and thus the play of this floating bearing are only determined by the shaft sealing rings in the Vespa engines. The tolerances in the old motors are large and, for example, we also use thicker housing seals today, so 7mm Simmerrings make sense!
WHY FKM / VITON®
The material is FKM (fluorocarbon rubber) extremely resistant to
- Heat
- Friction and
- Fuel type
- ethanol
Even super petrol fuel E5 in Germany currently has up to 5% ethanol admixture, with E10 even up to 10%, and the trend is rising. And did you know that this can vary from country to country? Possibly. Have you ever noticed in France, for example, that your engine runs differently? In other countries, the ethanol / alcohol content can be significantly higher.
A conventional shaft sealing ring cannot withstand this increasing ethanol admixture and can, for example, swell or soften on contact with fuels containing ethanol.
The bgm PRO In contrast, FKM / Viton® shaft seals offer one permanent protection. In addition, our Simmering with Viton® is compared to the conventional (blue) NBR shaft seals twice as temperature resistant. Further advantages of these modern shaft seals:
- extremely gas impermeable
- and very resistant to aging
SUITABLE FOR E10?
OK, so our Simmerrings from bgm have
- optimal dimensions and
- most modern materials
but for what are they now suitable?
A, with bgm PRO FKM / Viton® shaft sealing rings, equipped motor can also be used in motors with E10 fuel (10% alcohol) operate.
The modern and high-quality brown Viton® * sealing material is
- permanently resistant to ethanol / alcohol and
- also for engines with high temperature load
- and high speeds suitable.
bgm PRO FKM / Viton® shaft seals are therefore suitable for all engines! Just play it safe and install the modern Simmerrings right away. Whether for an original engine, mild tuning or extreme tuning and motorsport!
For reasons of environmental protection and in favor of maximum flexibility of the sealing lip, we deliberately refrain from additionally applying PTFE / Teflon® * to the sealing lip.
DOUBLE SAFE
The bgm PRO Shaft sealing rings offer a double seal as an additional feature:
All shaft seals that seal to the outside, to the atmosphere, have a so-called Dust lip. This is positioned and held in front of the actual sealing lip
- Dust,
- Dirt and
- Moisture away.
This further increases the very good stability.
CONCLUSION
The bgm PRO Shaft sealing ring set improves the installation clearance and, thanks to the excellent modern materials FKM / Viton®, offers an extremely long service life, combined with perfect fuel compatibility: it is even E10-resistant! The Simmerrings replace the old ones and of course fit without modifications.
Tip: We offer the Simmerrings individually as well as in a set and in a set with bearings!
* Viton® / Teflon® are registered trademarks of DuPont Dow Elastomers
